• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix car ignition switch replacement ignition (read this post here) Problems

The car ignition replacement won't begin to start until the ignition switch is sending an electrical signal to the starter motor. Normal wear and tear over time may result in the switch not functioning properly.

You can remove the steering column trim with specialized tools to gain access to the ignition cylinder module. Consult your repair manual to learn how to do it correctly.

1. Make sure to check the Switch

A malfunctioning switch is among the most frequently encountered ignition issues. It functions as bridge between two contacts, controlling the relays' activation and deactivation. Since it doesn't transmit the full power of devices such as the starter, it's a lighter-duty component that is less likely to fail. However it's still possible for the switch to become damaged or corrosion-prone.

A defective switch can be identified by a difficulty turning the key. This can be caused by a number of factors, including the wrong way to insert a key, or deteriorating the mechanism over time. It's not common to see people mix keys with keys from someone else's. This could cause mechanical damage.

If the switch isn't working, there are some things you can try before calling a locksmith. First, make sure that the battery is fully charged and that there are no electrical issues within the system. It is also important to test the voltage of each component to determine if they're capable of supplying enough power. Once you've completed these steps, it's time to begin troubleshooting.

Luckily, the ignition switch is easy to replace. It's connected to the ignition cylinder, a round module that connects everything. You'll need to use a flathead and something that is long enough to push the pin into. You can make use of anything from a paintbrush, to a kabob stick, but avoid anything that is hard as it could be broken into the hole.

Remove any trim pieces that cover the area around the switch when you're ready to go. After this, loosen and remove any screws that are holding the switch in place then gently pull it out. Depending on the model, you might need to disconnect any cables connected to it. You can learn how to do it in the instruction manual for your vehicle.

It is recommended to have the ignition switch replaced by an expert when it's not working. The replacement process involves disabling the steering column, which could trigger an unintentional airbag deployment if done incorrectly. It is recommended to allow your locksmith to take care of this.

2. Verify the Wire

Your car might not start if you are unable to turn the key or it isn't starting. This could be due to a variety of components in the ignition system. Understanding how the ignition system works will help you determine the cause of the problem and make the necessary repairs.

The ignition switch is a low-voltage multi-pole electrical switch that is turned by the key. It has four positions, which include "off", "accessory", "run" and the "lock". When the switch is locked (which is usually marked by an red light) the ignition circuit is activated and it is inaccessible to start your car.

You can use a voltmeter quickly test the ignition switch or coil. The voltmeter should read approximately 12.6 volts when the ignition switch is in the run position. If the voltage drops below that, it indicates there's an open circuit within the system. This could be at the solenoid, the battery or at the ignition coil itself.

Remove the electrical connector from the ignition switch to ensure there are no other components that could interfere with your test. Then set the voltmeter to the resistance or continuity mode and put one lead on one of the mobile ignition lock repair services switch's terminals. The other lead should be connected to the positive terminal on the battery. If the voltmeter shows "open" or doesn't show any voltage, it's time to replace the switch.

Make sure you use a new ignition key and a top-quality ignition cylinder when you replace the switch to ensure your vehicle runs and starts properly. Also, when you replace the ignition switch, be careful not to strike the ignition cylinder pins with your tools, or they'll get stuck and your engine won't start. In some vehicles, you'll need to remove the steering column and the gear selector to get access to the ignition cylinder. This isn't easy and should not be done unless you have an owner's guideline that says it's safe to do so. Otherwise severe damage to the steering column or shifting mechanism is likely.

3. Check the Cylinder

If you have tried the battery, the wiring, and the ignition switch but you are still unable to get your car started, it may be time to inspect the cylinder. It's the component that holds your key, and is mechanically connected to the lock on the steering wheel to ensure that thieves can't steer the car without a key.

You might be noticing that your key does not turn if the cylinder has worn out. The pins inside the cylinder may become stuck as they adjust to the shape of your key. This can cause your vehicle to not start. The cylinder could also be loose. Tapping it with the small tackhammer may help. Be careful not mixing with the springs and make sure your key is properly installed.

Another sign that your cylinder is in trouble is when you have to move the key around and try different positions before it gets started. This is a bad indication and needs to be fixed immediately, since it will only get worse over time.

To check the cylinder, you'll have to disconnect your battery, and then remove the cover from your steering wheel until you can access the ignition module. You should then be able to pull out the old ignition switch as well as the cylinder made of metal. If you don't own a spare switch, you may be able take your original ignition cylinder as well as switch to locksmiths for reuse as long they're in good shape. After replacing the switch and cylinder make sure you connect the wiring harness and secure it and reattach any covers, or panels you've removed.

4. Make sure you check the Spark Plugs

The spark plug is the last link in your ignition system chain. When it is damaged, the engine can't run. It could be that your vehicle won't start at all, or it will run badly. In either case, it's likely that one of several things are hindering or preventing electricity from jumping across spark plug gaps, which then ignites the air and fuel mixture inside your engine.

Be sure to use protective tools and gloves before working with your spark plugs. Spark plugs are hot and could cause serious injuries when you touch them with bare skin.